Sunday 1 December 2013

Free Airtel Gprs Trick ( Working And Tested ) 2nd December 2013


Free gprs, mms, airtel live, more let starts from free gprs via airtel live pls note this trick works only  on mobile with multi channel support it was not found by me .I Am Tested Its Work Fine With Me. You need a PC or a Laptop and the required connectivity tools ,ie.,Serial/USB cable OR Infrared Device OR Bluetooth dongle.........
 Now Follow These Stets >>>

1) Activate Airtel Live! ( It's FREE so no problems)

2) Create 1 Airtel gprs data accounts and select the

FIRST as the active profile.
CODE

Under DATA COMM
~~~~~~~~~~~~
GATEWAY : 100.1.200.99

APN : airtelfun.com

USERNAME : blank

PASSWORD : blank

PASS REQ : OFF

ALLOW CALLS : AUTOMATIC

IPADDRESS :100.1.200.99

DNSADDRESS 1 : 202.56.230.5

DNSADDRESS 2 : 202.56.240.5
 

DATA COMP : OFF

HEADER COMP : OFF

Under INTERNET PROFILES
~~~~~~~~~~~~~~~~

INTERNET MODE : HTTP or WAP (both works)

USE PROXY : YES

IP ADDRESS : 100.1.200.99

PORT : 8080

USERNAME : Blank

PASSWORD : Blank

3) Connect your mobile to the PC (or Laptop) and install the driver for
your mobile's modem.


4) Create a new dial-up connection using the NEW CONNECTION WIZARD as follows Connecting Device : Your mobile's modem

ISP Name : Airtel (or anything you like)

Phone Number : *99***1#

Username and Password : blank


5) Configure your browser and download manager to use the proxy
100.1.200.99 and port 8080.( My advice is to use Opera since you
can browse both wap and regular websites)


6) Connect to the dial-up account. You will be connected at 115.2
kbps (NOTE* 115.2 KBPS IS A SPEED BETWEEN UR PC AND PHONE ).


7) Pick up your mobile and try to access any site. You will get "Access
Denied."(except for Airtel Live!). IT DOES NOT MATTER.
Keep the mobile down.


8 ) On the PC ( or Laptop) open your browser, enter any address ,
press ENTER and.WAIT


9) After a few seconds the page will start to load and you have the
WHOLE internet at your disposal.
 

Quote: pls Note If u are getting any error wile dialing a dial up connection than go to
Control panel>> Phone and modem>>>select modem and click on its properties >>advanced

cntd
and enter the following initialization commands
CODEAT+CGDCONT=1, "IP","airtelfun.com","",0,0
and click on ok now connect to gprs it will be connected without any error

to improve the speed
go to run and type
ping -t 100.1.200.99
and pres enter
and minimize the window it will improve the speed delete...........


based on my experience u will get some of teh errors liek this
CODE
"Error 734: The PPP link control protocol was terminated"


possible solution
SYMPTOMS:-
If you try to establish a Point-to-Point Protocol (PPP) dial-up connection, you may receive the following error message:
Error 734: The PPP link control protocol was terminated.
As a result, you cannot establish a dial-up connection.


SE:-
This issue may occur if either of the following conditions are true: • Multi-link negotiation is turned on for the single-link connection.

-or-
• The dial-up connection security configuration is incorrectly configured to use the Require secured password setting.


RESOLUTION:-
To resolve this issue: 1. Click Start, point to Settings, and then click Network and Dial-up Connections.

NOTE: For Windows Server 2003, click Start, point to Control Panel, and then point to Network Connections.
2. Right-click the appropriate dial-up networking connection, and then click Properties.
3. Click the Networking tab, and then click Settings.
4. Click to clear the Negotiate multi-link for single link connections check box (if it is selected).
5. Click OK, and then click OK.
6. Double-click the connection, and then click Dial. • If this procedure resolves the issue and you can establish a dial-up connection, you do not have to follow the remaining steps in this article.
• If this does not resolve the issue and you cannot establish a dial-up connection, go to step 7 to continue to troubleshoot this issue.

7. Right-click the connection, and then click Properties.
8. Click the Security tab.
9. Under Security options, click Allow unsecured password in the Validate my identity as follows box, and then click OK.
10. Double-click the connection, and then click Dial to verify that you can establish a dial-up connection.


That's It Enjoy This Trick And Comment Below.
Note :: Try At Low Balance Otherwise Your Balance Deducted.
Like My Facebook Page For Latest Updates








6 comments:

  1. Thanks Friend Its Working In Mumbai...

    ReplyDelete
  2. working in rajasthan. but speed is 4-6 kbps.how can i speed up

    ReplyDelete
  3. I've xp-sp3 pc & nokia7230 set. How to apply 'FIRST as active profile. CODE
    Under DATA COMM' for my availability. I can't understand that part

    ReplyDelete
  4. successfully connected via dial-up.. But brwsr at the time of brwsing it says "could not connect".. Why?

    ReplyDelete